Roop
Good
Easy to work with, nice stable temperatures after install
۲۱٬۹۴۳٬۰۰۰ تومان

خرید TG Putty Thermal Grizzly Advance 100 گرم بتونه حرارتی غیر رسانای الکتریکی مدل TG-P-A-100 از میکرولس. [مشخصات فنی] بتونه حرارتی غیر رسانای الکتریکی ایده آل برای جایگزینی پدهای حرارتی سنتی در

Thermal Grizzly TG Putty Advance - 100 Gram - Electrically Non-Conductive Thermal Putty for GPU Modding and Thermal Pad Replacement
وزن
0.115 کیلوگرم
بتونه حرارتی غیر رسانای الکتریکی ایده آل برای جایگزینی پدهای حرارتی سنتی در تغییرات GPU. پرکننده شکاف انعطافپذیر که اختلاف ارتفاع بین اجزا را جبران میکند و تماس حرارتی بهینه را تضمین میکند. کاربرد آسان با استفاده از اسپاتول یا با دست. توصیه می شود هنگام استفاده دستی از دستکش استفاده کنید. به طور موثر اختلاف ارتفاع از 0.2 میلی متر تا 3.0 میلی متر را برای استفاده همه کاره در اجزای مختلف پل می کند. در سه نوع Basic، Advance و Pro موجود است که سطوح مختلف رسانایی حرارتی را متناسب با نیازهای خاص ارائه می دهد.
قیمت :
فروشگاه :

وزن
0.115 کیلوگرم
بتونه حرارتی غیر رسانای الکتریکی ایده آل برای جایگزینی پدهای حرارتی سنتی در تغییرات GPU. پرکننده شکاف انعطافپذیر که اختلاف ارتفاع بین اجزا را جبران میکند و تماس حرارتی بهینه را تضمین میکند. کاربرد آسان با استفاده از اسپاتول یا با دست. توصیه می شود هنگام استفاده دستی از دستکش استفاده کنید. به طور موثر اختلاف ارتفاع از 0.2 میلی متر تا 3.0 میلی متر را برای استفاده همه کاره در اجزای مختلف پل می کند. در سه نوع Basic، Advance و Pro موجود است که سطوح مختلف رسانایی حرارتی را متناسب با نیازهای خاص ارائه می دهد.
بر اساس نظرات آمازون
نظر شما میتونه به بقیه کمک کنه تا انتخاب بهتری داشته باشن خوشحال میشیم اگر تجربه تون از این محصول رو با ما به اشتراک بذارید!
نمایش ۶ نظر آمازون از ۵۶ نظر
Good
Easy to work with, nice stable temperatures after install
Not a substitute for a cpu paste, good performance for the right use case.
using this thermal paste on a custom mod of a notorious Lenovo Thunderbolt 3 gen 2 dock. It gets the job done with good thermal transmission. Please note this is not a replacement for thermal paste, and one must choose the right thermal compound (paste, pads, or putty) for the job at hand. Details on my use case follow: The dock was getting way to hot. Who would design a thermal aluminum block for a heatsink, and put it into a plastic case. Better to use a heatsink like I did, but my mod is not corporate slick, It's more like something off the Nebuchadnezzar (Matrix). I used a hot knife to get rid of half of the top of the plastic case to make room for the heatsink I cut to fit over the imperfectly flat aluminum block. I could only cinch it down with a couple of stout pieces of uninsulated copper wire so I did not want to use a large pad, which requires more compression. After the mod, the dock has been performing well with many fewer video glitches . Now I have to mod two more for my family. Why I chose this: it's about 10 sq. in. with perhaps 1/8 mm variance in the aluminum block of the dock so thermal paste is a non starter.. It is relatively low temp probably topping out at about 60 c so there will be minimal pump out due to thermal cycling.. I was able to clean the edges after application so the equipment will experience minimal melting, spillover etc. It was a hard choice between pads and this putty but I cannot apply lots of compression force because I am holding this together with tow copper wire bands. The bands hold the assembly together without movement, but only offer minimal compression. If I had installed screws in the heatsink, I would have enough compression for pads, but that ls another hour of labor or perhaps two, and requires exacting tolerances.
Grizzly putty advance
Ok perfetta usata su xbox. X
Enough for two laptops
Used on my laptop during repaste. Was good to work with. Enough for 2 laptops.
As expected
A bit difficult to apply due to it being quite thick, but works well. I opened up my MSI Claw and needed to replace the old and poorly applied putty and thermal paste. Once this thing was one with a fresh application of MX7 paste the temps have gone down by almost 10C. Not only does the handheld run considerably cooler, it also boosts for longer and subsequently the frame rates that I am getting are higher.
flexible and cool
Stuff is kinda annoying to apply but thermals are better than OEM dried out thermal pads and I didn't have to go through the trouble of sourcing however many weird sizes my card had