کیس کامپیوتر JONSBO D32 Pro Mesh مشکی Micro-ATX با پشتیبانی از BTF
کیس کامپیوتر JONSBO D32 Pro Mesh مشکی Micro-ATX با پشتیبانی از BTF
JONSBO D32 PRO Mesh Black Micro-ATX PC Case,High Compatibility Mini Desktop Case,A/B Mode for MB, Support MATX Back-Connect/BTF MB,365mm GPU/240AIO/163mm Air Cooler,ATX/SFX PSU, PC Gaming Case,Black
برند: Jonsbo
مشخصات فنی
نام تجاری
جانسبو
سازگاری مادربرد
مینی ITX، میکرو ATX
نوع مورد
مینی برج
کاربردهای توصیه شده برای محصول
تجارت
رنگ
مشکی
درباره محصول
JONSBO D32 PRO Micro-ATX PC Case-【قیمت بینظیر در هر کارایی】 - حجم 24 لیتری حالت A/B را برای مگابایت (مگابایت استاندارد و BTF مگابایت)، دستیابی به راهحلهای مختلف بهینهسازی سازگاری، ساخت آسانتر رایانه شخصی، راحتتر ارائه میدهد.
【سازگاری بالا】- ارتقاء Micro-ATX برای پشتیبانی از سخت افزارهای محبوب اصلی مانند مادربرد BTF، پردازنده گرافیکی 365 میلی متری حداکثر طول، PSU ATX/SFX-LSFX (به استثنای پلاگین 16 آمپر)، 240AIO، کولر هوای ارتفاع 163 میلی متر و غیره.
【طراحی بصری را بهینه کنید】: شیشه جانبی سکوریت شده سخت افزار کار مختصر و منظم را نشان می دهد. (قالب مدیریت کابل مادربرد قابل تنظیم برای مسدود کردن سیم های پیچیده قابل مشاهده)
طراحی بهینه تجربه نصب
【اندازه】:D396×W207×H314mm (شامل پا):
【پشتیبانی مگابایت】:استاندارد MINI-ITX/MICRO-ATX /MICRO-ATX (اتصال پشتی، کیس باید به حالت B تبدیل شود)
【Drive Bay】: 2.5 اینچ: تا 4، بستگی به سایر تنظیمات سخت افزاری دارد، 3.5 اینچ: تا 2 (به اشتراک گذاشته شده با 2 x 2.5 اینچ پایه)، به تنظیمات سخت افزاری دیگر بستگی دارد (بستگی به پیکربندی های سخت افزاری دیگر دارد)
【خلاصه PSU】: حداکثر L200mm (با دوشاخه 16A سازگار نیست)
【پشتیبانی از رادیاتور】:بالا، تا 240 میلی متر 【خلاصه خنک کننده هوای CPU】: در حالت A، H170mm (CPU Intel) یا 169mm (AMD CPU) در حالت B، H164mm (CPU Intel) یا 163mm (AMD CPU)
【فن】:بالا: 2 x 120 میلی متر / 2 x 140 میلی متر عقب: 1 x 120 میلی متر پایین: 3 x 120 میلی متر / 2 x 140 میلی متر
JONSBO D32 PRO Micro-ATX PC Case-【قیمت بینظیر در هر کارایی】 - حجم 24 لیتری حالت A/B را برای مگابایت (مگابایت استاندارد و BTF مگابایت)، دستیابی به راهحلهای مختلف بهینهسازی سازگاری، ساخت آسانتر رایانه شخصی، راحتتر ارائه میدهد.
【سازگاری بالا】- ارتقاء Micro-ATX برای پشتیبانی از سخت افزارهای محبوب اصلی مانند مادربرد BTF، پردازنده گرافیکی 365 میلی متری حداکثر طول، PSU ATX/SFX-LSFX (به استثنای پلاگین 16 آمپر)، 240AIO، کولر هوای ارتفاع 163 میلی متر و غیره.
【طراحی بصری را بهینه کنید】: شیشه جانبی سکوریت شده سخت افزار کار مختصر و منظم را نشان می دهد. (قالب مدیریت کابل مادربرد قابل تنظیم برای مسدود کردن سیم های پیچیده قابل مشاهده)
طراحی بهینه تجربه نصب
【اندازه】:D396×W207×H314mm (شامل پا):
【پشتیبانی مگابایت】:استاندارد MINI-ITX/MICRO-ATX /MICRO-ATX (اتصال پشتی، کیس باید به حالت B تبدیل شود)
【Drive Bay】: 2.5 اینچ: تا 4، بستگی به سایر تنظیمات سخت افزاری دارد، 3.5 اینچ: تا 2 (به اشتراک گذاشته شده با 2 x 2.5 اینچ پایه)، به تنظیمات سخت افزاری دیگر بستگی دارد (بستگی به پیکربندی های سخت افزاری دیگر دارد)
【خلاصه PSU】: حداکثر L200mm (با دوشاخه 16A سازگار نیست)
【پشتیبانی از رادیاتور】:بالا، تا 240 میلی متر 【خلاصه خنک کننده هوای CPU】: در حالت A، H170mm (CPU Intel) یا 169mm (AMD CPU) در حالت B، H164mm (CPU Intel) یا 163mm (AMD CPU)
【فن】:بالا: 2 x 120 میلی متر / 2 x 140 میلی متر عقب: 1 x 120 میلی متر پایین: 3 x 120 میلی متر / 2 x 140 میلی متر
ابعاد مورد D x W x H39.6D x 20.7W x 31.5H سانتی متر
نام مدلD32
سازندهJONSBO
شماره مدلمش D32 pro
نظرات مشتریان4.64.6 از 5 ستاره (32) 4.6 از 5 ستاره
مکان آنتنتجارت
امتیاز و نظرات
4.6
۳۲نظر
بر اساس نظرات آمازون
نظر شما میتونه به بقیه کمک کنه تا انتخاب بهتری داشته باشن خوشحال میشیم اگر تجربه تون از این محصول رو با ما به اشتراک بذارید!
نمایش ۵ نظر آمازون از ۳۲ نظر
Jason Crawford
Reviewed in the United States on 10 November 2025
I love this case! Best case ever!
I almost purchased the Asus AP201 until I found this case on Jonsbo's web site before it was available on Amazon. Somehow Amazon showed 1 in stock in the middle of the night when I was looking at my cart before it was officially available. Anyhow this thing is fantastic. I wanted something as small as possible, lightweight, that could fit a few 2.5" drives, great ventilation for a slow silent fan, and didn't have any weird looking clear panels. This is also for a low power PC build with a micro PSU and a large 12v power brick. The front PSU mount is perfect for stashing the power brick inside the case up front. The paint on this is perfect, though you may want to add some nylon washers for the screws holding the sides on so the paint doesn't scratch. The feet on this are also nice and sturdy which is a great upgrade from my last case. It came with all the screws/hardware I needed for my motherboard and drives. The only annoyances for me are: 1. It takes it little more effort to get at the expansions slots since you have to remove several screws and the bracket they hold in before you can get at the slots. 2. Getting the drive cables mashed into the side of the case and under the cover was a bit of a challenge as the 2 primary 2.5" drive mounts are under the motherboard. Thank you Jonsbo!
5.0
Lance Meyers
Reviewed in Canada on 25 April 2026
Impressive matx case with an itx footprint.
This has to be my favorite case i've ever owned and it's very well priced considering usually these small cases come at a premium price. It fit my Sapphire rx 7900 XTX, my evga 1000w supernova power supply and thermals are good as far as the limitations for these small form factor case. It doesn't run as hot as you think it would however I have the mesh side panel version and not the tempered glass. So keep in mind if you buy the tempered glass version i'd expect higher temps. As far as my cooling setup I found I had the best result by using Rear fan 120m exhaust, top-rear fan 140mm exhaust, no bottom fans because if you have a 3 slot GPU you wont fit fans under it so it's best to treat the GPU as a 3 fan intake. With that said, the temps are reasonable with my 7800X3D staying around 60-65c with a Bequiet Dark rock Pro 4 air cooler on top and the GPU being around 70-75c. Again this is my favorite build i've ever had, it has the footprint of an ITX case while still giving you the options of a MATX case. Building my PC into this case wasn't too hard either, i didn't even look at their instructions however if you're a novice maybe give the instructions a read as you may need to remove the tray under the power supply to fit your cables. One more thing for buyers, I would strongly recommend sizing up components for this case before buying as there will certainly be some components that wont fit if you aren't considerate to it's size. With that said though if you plan carefully you can still have a 3 slot powerful gpu, large air cooler for cpu and a 1000w atx power supply. Plan accordingly.
5.0
SpoiledBroth
Reviewed in Canada on 22 January 2026
Great sff/matx case with support for full size psu
Excellent case. Thoughtfully designed, good fit and finish. Easy to build in. Looks great as well. I only wish the mesh was more modern fabric type. Otherwise it's a 9/10 case.
5.0
Emonkie
Reviewed in the United States on 31 July 2026
Good quality, good price
I have been shopping for a case for a little while now. I really like this case because it is under $100 and has pretty good front i/o. Power button feels solid, overall build quality seems good. I especially like that it isn't overly huge (but still quite big). I went with this case as I think it is a little more beginner friendly than others for a first time builder like myself. Definitely good quality and good price.
5.0
J. Swanson
Reviewed in the United States on 22 September 2026
Good gaming case with some minor flaws
This was my first offering from JONSBO, and aside from a couple of quibbles, I was pleased. The Good: [+] Price: reasonable cost for the features provided. [+] Compatibility: can fit some very large GPUs (including 4090/5090-class), great for gaming builds [+] Connectivity: 1 USB-C, 2 USB-A, and an audio jack in front. Many smaller form factor cases only have 2 USB ports The Bad: [-] Quality control: the side panels aren't entirely flush. Hard to notice normally, but easy to catch when assembling the case. [-] Design choices: for some reason, there are two or three screws on the bottom of the case that extend beyond the bottom panel. These screws are sharp and can gauge any uneven surfaces the case may be placed upon. An odd decision when shorter, properly-fitting screws could have been used. I resolved this by using a rotary tool (dremel) to trim the excess. Overall, a worthwhile buy if you can get a good deal. Here's hoping they fix the QC and design issues in further iterations.